【Product Features】
- Built-in installation presence sensor, standard zhaga20 interface
- Adopt 24GHz patented microwave antenna technology, support 4m max.
installation height
- With German RF technology, 5 years product warranty
- Motion, minor-motion, and daylight sensor function
- Applicable for washrooms, living rooms, kitchens and other
environments where motion, minor motion detection required
- Grouping networking by 2.4G wireless, no need pairing or gateway.
- Output 0-10V dim or PWM dim, 2-step/3-step dim function.
- All sensor parameters can be set by remote control.
【Parameters】
| Input |
| Rated Voltage | 12±1VDC |
| Working Current | 90±5mA |
| Ripple Voltage | <100mVp-p |
| Output |
| Output Signal | MC182D 99 B1 | MC182D 99 1 B1 |
| 0-10VDC dimming signal | PWM dimming signal |
| Sensor Parameters |
| Working Frequency | 24GHz~24.25GHz,ISM band |
| Transmitting Power | 6dBm Max. |
| Detection Area | 100% /75%/50%/25%(MH17)；100% / 50%/25%(MH15) |
| Hold Time | 30s/1min/3min/5min/10min/20min/30min(MH17)； 30s/1min/3min(MH15) |
| Stand-by Period | 0s/10s/1min/3min/5min/10min/30min/+∞(MH17); 5min/10min/ +∞(MH15) |
| Stand-by DIM Level | 10%/ 20%/ 30%/ 50% (MH17);10%/ 30%(MH15) |
| Daylight Sensor | Daylight threshold | 5Lux/15Lux/30Lux/50Lux/100Lux/150Lux/999Lux(Disable)(MH17) 15Lux/50Lux/(Disable)(MH15)(Ambient light diffusing state) |
| Daylight harvesting | 100L/200L/300L/400L/500L/600L/Disable (MH17press“P”enter daylight harvesting mode) |
| Stand-by Dim Level | 10%/ 20%/ 30%/ 50% (MH17);10%/ 30%(MH15) |
| Detection Range (Radius) | Ceiling installation 3m high Motion and minor motion: r≥2.5m Test condition: 100% sensitivity, 60㎡indoor open space |
| Installation Height | 3m (4m Max ) |
| Wireless Parameters |
| Operating Frequency | 2.400-2.483GHz |
| Transmitting Power | 6dBm |
| Group | One group max nodes 32 Pcs |
| Transmitting Distance | 15m MAX(Point-to-point open area transmission distance) |
| Environment |
| Working Temperature (Ta) | -35℃-60℃ |
| Storage Temperature | -40℃~+80℃ humidity: ≤85% (non-condensing) |
| Certification Standards |
| Certification | CE |
| Environmental Requirements | Comply with RoHS 2.0 , Reach requirements |
| IP Rating | IP20 |
| Protection Class | Class II |
| Others |
| Wiring | 3 pin PH2.0 terminal |
| Installation Requirements | External zhaga book20 installation |
| Packaging Requirements | Clapboard + Carton (K=A) |
| Net Weight | ±3g |
| Lifetime | 5 years warranty @Ta |
【Function description】
RON-OFF function | Stand-by Period be set to “0s” |
| R2-step dimming | Stand-by Period be set to “+∞”, Daylight sensor be set to “High” |
| R3-step dimming | Stand-by Period be set to “5min/10min” |
| RDaylight harvesting | Stand-by Period be set to “+∞”, Daylight sensor be set to “LOW/MED” |
| Daylight priority | N/A |
| RGrouping | Remote group “1-8” and set Rx signal for sensor |
【Diagram】
【Detection Range】
Motion signal Minor motion signal
Human presence: detect the human body in the detection area to carry out big movement signals (walking) to trigger the induction and output high level (such as control lights on and off), and then
detect minor motion signals (body leaning forward, backward, limb swinging, shaking the
head, typing, playing mobile phones and other minor motions.) as well as the detection of human respiratory vital signs caused by
the abdominal cavity, chest expansion etc to maintain output high level (such as control lights always on)
Human absence: no signal detected in the detection area and output low level
(control lamp off)
【Remote】MH15
MH17
【Initialization】
After power on, the sensor automatically turns on light at 100%
brightness and self-check for 45s-60s. During the initialization,
the sensor is not able to detect movement. It enters sensing mode
after initialization, and during which, the lamp maintains at 100%
brightness.
【Default setting】
Sensitivity: 100%, Hold time: 5s, Daylight sensor: Disable,
Stand-by period: 0s, Stand-by dim level: 20%
【Application Notice】
l The sensor should be installed by a professional electrician.
Please turn off the power before installing, wiring, changing the
configuration.
l The product has good penetration ability to plastic, wood, etc.,
but the microwave module antenna should not have metal accessories
or metal shells, glass shells, etc.in direct front or nearby,
otherwise it will affect the antenna transmission and reception.
l The sensing distance will be affected by the installation height,
the size of the object to be detected, the speed of movement, the
impact of the installation environment, and the sensing distance in
different directions will have a certain degree of variability.
l The daylight threshold is in a sunny environment, no shadows, and
ambient light diffuse reflection conditions. In different periods,
climates, and environments, the daylight value detected by the
light sensor may be different.
l The installation distance of the product is recommended to be more
than 1.5m; the installation distance between the product and the
router should be more than 1.5m, so as not to cause interference to
the normal operation of the microwave sensor.
l The mounting plane of the product (e.g. aluminium substrate, PCB
board) needs to be at a certain height difference from the antenna
plane of the microwave module, and the antenna plane of the
microwave module should be higher than the nearby plane by more
than 5mm in order to achieve the best detection effect.
l DC regulated power supply with stable output voltage, low current
and ripple coefficient must be used, the ripple of the power supply
should be less than 50mV, and the minimum load current of the power
supply should be more than 120mA, and it is also recommended to set
up an electrolytic capacitor of not less than 100uF at input power
supply VCC terminal.
l Product installation as far away as possible from large metal
equipment, pipelines, air conditioning vents, exhaust vents, smoke
machines and other scenes, so as to avoid equipment vibration
affect the detection effect.
l Microwave module should avoid close to the AC drive power supply,
be away from the drive power supply rectifier bridge, transformer,
switching tubes and other high power devices, to avoid high
frequency signals interference to normal operation of the microwave
module.
l Product design: the antenna surface of the microwave module and its
nearby circuits to avoid the flow of large currents, avoiding
transformers or high frequency components nearby, distance should
be more than 10mm as far as possible.
l When wiring, the antenna side and the component side on the back of
the product should not be covered by wires or have large currents
flowing through, so as not to affect the normal operation of the
sensor.
l The front of the product and nearby can not be equipped with metal
accessories or glass block, so as not to affect the normal
operation of the sensor, while the thickness of the plastic as far
as possible to choose less than 1mm, too thick will affect the
detection of microwave modules and directionality; microwave
antenna plane and the shell distance should be greater than 3.2mm
l The antenna surface of the product and the metal plane (aluminium
substrate, iron shell) need to be a certain height difference, the
recommended distance is more than 0.5mm.
When product structure, power supply mode/circuit, sensor antenna
front cover, etc. changes, pls notify the sensor manufacturer to
confirm, so as not to cause the product to work improperly.
Otherwise, the manufacturer does not bear any corresponding
responsibility for the abnormality.
